Get started with ECAD
A RunMat ECAD design is a schematic in a .circuit file and its board in a .circuit.layout file beside it. The Desktop shows the schematic, the board and the 3D board as tabs of one design; the agent and the command line read and write the same text.
1. A schematic
Create sensor.circuit. Components name library parts by MPN, and connect lists join pins into nets:
runmat 0.7
std 1
// A 3.3 V rail from a 5 V input, a power LED, and an RC filter ahead of an ADC input.
circuit sensor {
root = main
net_class power = { track_width = "0.40 mm", clearance = "0.20 mm" }
variant lite = { overrides = { D1 = not_fitted } }
sheet main {
component U1 = { part = "LDO-3V3-SOT23" }
component C1 = { part = "C0805-10U" }
component C2 = { part = "C0402-1U" }
component D1 = { part = "LED0603-G" }
component R1 = { part = "R0402-1K" }
component R2 = { part = "R0402-10K" }
component C3 = { part = "C0402-100N" }
component P1 = { part = "PAD-WIRE-20AWG" }
component P2 = { part = "PAD-WIRE-20AWG" }
component P3 = { part = "PAD-WIRE-20AWG" }
net GND = { class = power, global = true, power_flag = true }
net VIN = { class = power, power_flag = true }
net "+3V3" = { class = power, global = true }
connect = [net.VIN, "P1.1", U1.VIN, U1.EN, "C1.1"]
connect = [net.GND, "P2.1", U1.GND, "C1.2", "C2.2", D1.K, "C3.2"]
connect = ["net.+3V3", U1.VOUT, "C2.1", "R1.1"]
connect = [net.LED, "R1.2", D1.A]
connect = [net.SENSE, "P3.1", "R2.1"]
connect = [net.ADC, "R2.2", "C3.1"]
no_erc = [U1.NC]
}
// The 10 k / 100 nF filter ahead of the ADC: a 159 Hz corner.
simulation filter {
sheet = main
source VS = { p = net.SENSE, ac = 1 V, pulse = { from = 0 V, to = 1 V, delay = 1 ms, rise = 1 us, fall = 1 us, width = 20 ms, period = 40 ms } }
tolerance resistors = { match = "R*", value = 1 % }
tolerance capacitors = { match = "C*", value = 10 % }
analysis step = tran { stop = 10 ms, step = 10 us }
analysis response = ac { from = 1 Hz, to = 100 kHz, points = 50 }
probe = [net.SENSE, net.ADC]
measure corner = { of = response, bandwidth = net.ADC, spec = { min = 140 Hz, max = 180 Hz } }
measure rise = { of = step, rise_time = net.ADC, from = 1 ms, to = 10 ms, spec = { max = 3 ms } }
measure settled = { of = step, final = net.ADC, spec = { min = 0.99 V, max = 1.01 V } }
}
}net_class powersets the track width and clearance the board uses for power nets.variant litebuilds the board without the LED.simulation filterchecks the RC filter's corner and step response against limits.
2. Check it
runmat-design check sensor.circuitThe check runs the electrical rules, the design-review suites and every simulation's measures, prints each finding, and exits with status 1 on an error. See Rules and checks.
3. Start the board
Create sensor.circuit.layout with its outline and the fabricator's limits:
runmat 0.7
std 1
use circuit sensor
layout sensor {
outline = [[0, 0], [40, 0], [40, 25], [0, 25]]
limits = { clearance = 0.15, track = 0.15, via_diameter = 0.45, drill = 0.2, annular = 0.1, hole_to_hole = 0.25, copper_to_edge = 0.3, silk_to_pad = 0.1, microvia_drill = 0.1 }
net_class power = { track_width = 0.4 mm, clearance = 0.2 mm }
}A check of the new board reports the schematic changes it has not taken yet (board_out_of_sync); the board tab's Update board takes them, adding the components as footprints to place. Then routing, pours and vias are added on the canvas or by the agent. DRC runs as the board changes. See Board layout.
4. Fabrication outputs
runmat-design export sensor.circuit.layout --format fabrication --out fabThis writes Gerber, drill, the fabrication drawing, IPC-2581, ODB++, the IPC-D-356A netlist, and the BOM and pick-and-place file of each variant. See Fabrication outputs and netlists.
Next
- Guides: Draw a schematic, Lay out a board, Run a circuit simulation and Make fabrication outputs.
- ECAD file reference: every statement in
.circuitfiles. - Simulation sections and measures: analyses, measures and limits.
- The parts library: parts, declarations and models.